Set Up Your PawFence
No wires, no digging, and no app needed. PawFence builds a GPS boundary around your yard in minutes. This guide shows you how to set up both fence modes: Polygon Fence for any shape you want and Circular Fence for a simple round boundary.
Safety First: Before You Begin
- Keep the collar off your dog while you set up and test your boundary.
- Set static to 0 during setup to avoid accidental corrections.
- Keep the collar and remote together as you walk your yard.
Once your boundary is set and tested, introduce your dog to it gradually, with you there to supervise.
Polygon Fence Mode
Perfect for yards that aren't a simple circle, like a rectangular backyard, an L-shaped lot, or one section of your property. Walk the corners and you're done.
Before You Start
- Collar: charged and turned on
- Remote: charged and turned on
- Boundary markers: the flags in your box
- Open outdoor spot with a clear view of the sky
Pair the collar to the remote
- Long-press the power button on the collar until you hear a sound and the light flashes red and blue.
- On the remote, make sure you're on Channel 1, then long-press the Channel button.
- Both will beep, and a battery bar appears under the collar on screen. You're paired.
Wait for satellite signal
A green 60-second countdown appears after pairing. Let it count all the way down to zero.
At the top left of the screen you'll see GPS with a number next to it, starting at 00. Once the countdown is done, that number starts climbing and moving up and down. Those are your satellites, which means the collar is picking up signal.
Place your boundary markers
Walk your yard and push a marker into the ground at each corner of your shape. Your Polygon Fence can have up to 6 points, but feel free to use as many markers as you like along the boundary.
- How do they help you? You'll know exactly where to stand and exactly where to walk for each point.
- How do they help your dog? Your dog can see the boundary, which makes training much faster and easier.
Walk and map your points
- Long-press the Polygon Fence button on the side of the remote to open the Polygon Fence Setup screen.
- Stand at your first marker and long-press +. You'll see P1 show up at the top left and a dot in the middle of the screen.
- Walk to the next corner of the shape you're building and long-press + again. Repeat at every corner. Your shape builds as you go: first a dot, then a circle, then a triangle, then a rectangle, and so on.
Activate and test
- Long-press the left button (the one with the vibrate icon) until your shape's outline turns green. Your fence is now active.
- Test it: walk outside the boundary and the collar will go off. Walk back in and you'll see the collar as a live dot inside your shape.
More Tips & Features
Setting up a 2nd or 3rd dog
- Press the Channel button to switch to Channel 2 (or Channel 3).
- Long-press the new collar's power button until it flashes red and blue.
- Long-press the Channel button on the remote. When both beep and a battery bar appears under the collar icon, you're paired.
- Long-press the Polygon Fence button and walk the same markers in the same order, long-pressing + at each one.
- Activate the fence the same way as in Step 5.
Turn the fence on/off
Long-press the same left button you used to activate it to switch the fence off or back on.
- Green outline: the fence is on and active.
- White outline: the fence is off or not set up yet.
Manual correction
Dog getting too close to the line? Use the vibrate, sound, or static buttons to call them back. Press the mode you want, then press up or down to set the intensity.
Lock the remote
Long-press the lock button on the left side of the remote to lock it, and long-press again to unlock. It also locks itself after 30 seconds.
Night light
Tap the Polygon Fence button once to light up the collar so you can find your dog in the dark. Tap again to turn it off.
Training tip 🐶
For the first few days, walk your dog on a leash up to the boundary markers. Let them see the flags and feel the collar's warning at the line. Dogs learn much faster when they can see the boundary as well as feel it.
Circular Fence Mode
The fastest way to set a boundary. Stand in the middle, pick how far your dog can roam, and PawFence draws a circle around that spot.
Before You Start
- Collar: charged and turned on
- Remote: charged and turned on
- Center point: know where the middle of your circle will be
- Open outdoor spot with a clear view of the sky
Pair the collar to the remote
- Long-press the power button on the collar until you hear a sound and the light flashes red and blue.
- On the remote, make sure you're on Channel 1, then long-press the Channel button.
- Both will beep, and a battery bar appears under the collar icon on screen. You're paired.
Wait for satellite signal
A green 60-second countdown appears after pairing. Let it count all the way down to zero.
At the top left of the screen you'll see GPS with a number next to it, starting at 00. Once the countdown is done, that number starts climbing and moving up and down. Those are your satellites, which means the collar is picking up signal.
Set your center point
- Walk to the spot you want as the center of your circle and stand there.
- Long-press the left button, the same button as vibrate. It has a marker icon right below the vibrate icon.
- You'll hear two beeps. That means your center point is set.
Set your fence distance
- Long-press the right button, the same button as beep, to open the distance setting. It has a ruler icon right below the beep icon.
- Press up or down to choose how far from the center point your fence will be.
- Press the ruler button again to save it. Your fence is ready to go.
Set your correction levels
Choose how the collar lets your dog know they're near the edge. Press the mode you want, then press up or down to set the intensity:
- Static: press the static button at the top, then up or down to set the level.
- Vibrate: press the vibrate button on the left, then up or down to set the level.
- Beep: press the beep button on the right, then up or down to set the level.
These levels are used both for manual correction and for the Circular Fence itself.
Circular Fence Tips
Setting up a 2nd or 3rd collar
- Press the Channel button to switch to Channel 2 (or Channel 3).
- Long-press the new collar's power button until it flashes red and blue.
- Long-press the Channel button on the remote. When both beep and a battery bar appears under the collar icon, you're paired.
- Stand at your center point and long-press the marker button until you hear two beeps.
- Long-press the ruler button and set the distance the same way as in Step 4.
Turn the fence on/off
Tap the lock button once (a quick tap) to turn Circular Fence off. Tap it again to turn it back on.
Lock the remote
Long-press the lock button on the left side of the remote to lock it, and long-press again to unlock. It also locks itself after 30 seconds.
Night light
Tap the Polygon Fence button once to light up the collar so you can find your dog in the dark. Tap again to turn it off.
Need a Hand?
Our team is happy to help you get set up. Just reach out any time at support@shoppawfence.com.
Pro tip: Send us a short video showing exactly where you're getting stuck. It helps us spot the problem right away, so we can get you fixed up and your fence running as fast as possible.